Version: v1.6
Date: 2020-03-10
BFA-LFA-ADFA
- Change name of the filters:
– NB becomes Fix-1
– WB becomes Fix-2 - Minor bug fix
BFA
-
Version: v1.6
Date: 2020-03-10
BFA-LFA-ADFA
- Change name of the filters:
– NB becomes Fix-1
– WB becomes Fix-2 - Minor bug fix
-
Version: v1.2
Date: 2018-12-06
BFA-LFA
Fixed: improved alarm management if noise on the line is revealed when display is switched on
-
Version: v1.1
Date: 2048.10.10
BFA-LFA
Fixed: Alarm management improved when noise on the line is revealed
Fixed: Minor Bugfix
LFA
-
Version: v1.6
Date: 2020-03-10
BFA-LFA-ADFA
- Change name of the filters:
– NB becomes Fix-1
– WB becomes Fix-2 - Minor bug fix
-
Version: v1.2
Date: 2018-12-06
BFA-LFA
Fixed: improved alarm management if noise on the line is revealed when display is switched on
-
Version: v1.1
Date: 2048.10.10
BFA-LFA
Fixed: Alarm management improved when noise on the line is revealed
Fixed: Minor Bugfix
MAT244
-
Version: v1.13
Date: 2021-06-14
MAT244
- add: bug fix: if there was a disconnection of the antenna remote control while trying to modify a parameter remotely, the matrix could freeze
-
Version: v1.12
Date: 2019-07-23
MAT244
- add: support of new antennas
- fix: minor bugfix of Ethernet management (Eth. Busy)
-
Version: v1.6
Date: 2018-02-07
MAT244
Fixed device name when saving preset
Fixed updating of the main page when a preset is loaded
Fixed activation command from PC-
Version: v1.7
Date: 2018-02-07
MAT244
Fixed refresh of the main page when matrix type is changed remotely
Fixed updating of the main page when a preset is loaded-
Version: v1.8
Date: 2018-02-07
MAT244
Fixed panel lock bug, if you were doing a discovery of antennas and at the same time an overloaded alarm occurred on an antenna.
MAT288
-
Version: v1.13
Date: 2021-06-14
MAT288
- bug fix: if there was a disconnection of the antenna remote control while trying to modify a parameter remotely, the matrix could freeze
-
Version: v1.12
Date: 2019-07-23
MAT288
- add: support of new antennas
- fix: minor bugfix of Ethernet management (Eth. Busy)
MCR41S-42S
-
Version: v3.27.0
Date: 2022.07.27
MCR42
bug fix:
- Occasionally, while working in ENS, audio output level was low
- Minor bug fix
-
Version: v3.26
Date: 2022-03-23
MCR42
- Added ENS compander
- Added MTP60 compatibility (SYNC and 16 bit battery data)
- Fixed minor bug fix
-
Version: v3.24
Date: 2019-02-14
MCR42
- added support for new bands: Band 8 (B8: 940-960MHz) and Band P (BP:806-810MHz)
- modified SYNC process for compatibility with Narrow band Transmitters
- added Tone Squelch delay setting: configurable delay for the activation of the audio when the tone squelch is detected
- added new panel lock mode (“ENC *”) which, when activated, loads all parameter values to default, except for:
-
- Compander: ENC
- Analog LINE level: + 12dBu
In ENC lock mode * all panel parameters are locked except for: Change group / channel / frequency, Audio levels settings
-
-
Version: v3.21
Date: 2017-11-24
MCR41-MCR42
- added: MCR42-S3 Version Management *
- added: lock panel parameter in the preset
- added: displaying the last loaded preset to the preset pages
- fixed: wrong level battery indication on 688/Manager with SEN compander
- fixed: wrong LINE level after the change from analog to digital
- fixed: wrong Compander selection after the factory preset
- fixed: wrong display group/channel after the factory preset when one receiver is OFF
- fixed: wrong COM level after restoring
- fixed: wrong indication of Change Group/Channel after saving of presets
- fixed: deviation bar management issue when the calibration tone is activated
*NOTE: MCR42-S3 version is the latest hardware version of MCR42.
It increases the max analogue audio level to +18dBu for LINE and COM outputs (on the previous version the max level was +12dBu)
It allows the selection by software of the type of outputs on the Top Feed and Base. Based on the “Line Mode” choose, different output options are available:
– if LINE mode is set on Analog, you can choose between Line-A (Analog) and COM on both Top Feed and Base (socket)
– If LINE mode is set on AES3 (digital), you can choose between Line-D (digital) and COM on both Top Feed and Base (socket)
-
Version: v3.18
Date: 2017-11-23
MCR41-MCR42
fixed: display of the audio bar level after calibration tone – even if the calibration tone is stopped, the audio bar level shows the output level of the previous calibration tone.
Steps to replicate the issue:
– Enter into the circular menu and go to the audio information.
– Start calibration tone on RX1
– Do nothing, just wait until the receiver jumps back to the status screen.
– When jumping back to the status screen the calibration tone stops which is correct but the audio bar in the status screen still shows for RX1 the output level of the calibration tone
This problem happens only with RX1, not happens with RX2.fixed: problem to save the compander in the memory during loading of the preset.
-
Version: v3.17
Date: 2016-10-04
MCR41S-42S
new – management of Preset menu:
The first 3 preset can only be modified by PC (default name PRESET_x). The following two are editable by the receiver as well (default name USER_x)
Menu option for the Preset changed from “Restore” into “Load” and now it’s the first option available on the main menu.new – ask for a factoory restore settings when recognized a different slot-in:
during the power on of the receiver, in case it recognizes an slot-in different from what was previously installed, the unit asks if you want to do a factory restore settings.MCR54
-
Version: V2.3.0
Date: 2023-04-20
MCR54
NOTE:
Use Wisycom Manager 3.4 or later to update.
New:
- Added JNS Compander.
- Added PTT Management (Compatibility with Wisycom Manager 3.4 or higher).
- New user interface (added PTT selection and Audio Routing Menu).
Bug Fix:
- Audio routing on PTT while using SEN compander.
- Fixed audio bar data initialization.
- Fixed base analog level control on MRK16.
- Fixed Rx3/Rx4 output selection.
- Fixed No digital audio output with BPA54 and Ikegami slot-in.
-
Version: v1.23.0
Date: 2022-07-08
MCR54
Added:
- BT App compatibility
- Compander NONE-d75 narrowband compatibility
- Antenna tip in INFO page
Fixed:
- Frequency scan forbidden on SYNC group
- Improved antennas selection on bottom for MRK16 base
- Scan functionality improvements
- TX battery icon optimized
- Graphic deviation audio bar optimized
- While into MRK16, changed highlighting receiver indication
- Minor bugs fix
-
Version: v1.22.0
Date: 2022-02-16
MCR54
New:
- Added compatibility with MRK16
- Added SYNC process with MTP60
- Improved compatibility with MTP60 (ENS compander)
- Improved display layout
- Added support of Narroband modulation for NONE_75us compander
- Activation of ENS compander if not available
- Set quick access to Headphone page pressing EXIT+SEL buttons
- Changed default receiver name from “RECEIVERn” to “RXn”
- Changed compander after a Factory Preset (from ENR to ENS)
Bug FIX
- Fixed bump noise issue during RX selection headphone
- Fixed group selection issue in SCAN Channels function
- Fixed set frequency issue after a SCAN Frequency function
-
Version: V1.10
Date: 2021-08-06
MCR54
Added:
– Single Rx view page.
– Removed 3 seconds SAVE confirmation button.
– Removed “Saved” popup when a parameter is changed.
– Logo updated.
– Modulation mismatch pop up updated.
– New “Set to All” function to automatically assign the best 4 scan results to the currently active receivers.
– New RF bars from 0 to 80 dBuV in 10 dBuV steps.
Bug FIX:
– Fixed missing compander/ChMod/cal tone control when the receiver is not active.
– Fixed mute/unmute control on AUX out.-
Version: v1.9
Date: 2021-06-18
MCR54
Bug Fix:
- Minor bug fix.
- Tone Squelch is enabled only if the compander supports it.
- When receiver is out of the front end, input passband filter (BW=32MHz), audio and RF bars are disabled
-
Version: v1.7
Date: 2020-11-18
MCR54
Added:
– IRDA bridge feature for remote control of Wisycom Transmitters by Wisycom Manager equal or higher v3.1.0
– Channel SCAN command for compatibility with Sound Device SL-2
– 8/16-bit telemetry decoding
– Improved multiple frequency set up after a Channel SCAN
– Improved shutdown sequence
– OFF timeout display unit changed from minutes to seconds
– Squelch mode OFF removed
– USER mode Noise squelch range reduced to 8-25 dB
– In the main overview display RF Squelch level replaced with Squelch modeBug Fix:
– Calibration tone issue
– Graphic artifact after the Freq. SCAN
– Generic minor graphic issues
– Serial Communication stall when incoming data have baud rate different from 115200-
Version: v1.5
Date: 2020-08-31
MCR54
Fixed:
- minor bug on frequency settings
- seldom random conditions could trigger a device software shut down
-
Version: v1.3
Date: 2020-07-23
MCR54
- Fixed USB startup freezing
- Fixed Calibration Tone Status
- Fixed EXT_ON Pin Logic
- Fixed Audio Bar Attack-Release
- Added Socket SN under Info Menu
- Menu Text Updates
- Power On Time Decrease
- Updated Sockets Compatibility
- Updated Minor DSP Parameters
- Introduced Selectable Level on SX Sockets
-
Version: v1.2
Date: 2020-07-02
MCR54
- changed Squelch mode name (from “Aggressive” to “Long Range”)
- changed default value of delay of Squelch ON (from 500ms to 0)
- changed Noise Squelch hysteresis (from 8dB to 4dB)
- added RTS/CTS Bluetooth control
- added Wisycom protocol compatibility on Bluetooth UART
- added UART communication with the rear panel
- fixed led issue when receivers are OFF
- fixed TX reference warning during battery TX alarm
- fixed initialisation of the AES output at 48KHz
MCR54-DUAL
-
Version: v2.3.0
Date: 2023-04-24
MCR54-DUAL
NOTE:
Use Wisycom Manager 3.4 or later to update.
New:
- Added JNS Compander.
- Added PTT Management (Compatibility with Wisycom Manager 3.4 or higher).
- New user interface (added PTT selection and Audio Routing Menu).
Bug Fix:
- Audio routing on PTT while using SEN compander.
- Fixed audio bar data initialization.
- Fixed base analog level control on MRK16.
- Fixed Rx3/Rx4 output selection.
- Fixed No digital audio output with BPA54 and Ikegami slot-in.
-
Version: v1.23.0
Date: 2022-07-08
MCR54-DUAL
Added:
- BT App compatibility
- Compander NONE-d75 narrowband compatibility
- Antenna tip in INFO page
Fixed:
- Frequency scan forbidden on SYNC group
- Improved antennas selection on bottom for MRK16 base
- Scan functionality improvements
- TX battery icon optimized
- Graphic deviation audio bar optimized
- While into MRK16, changed highlighting receiver indication
- Minor bugs fix
-
Version: v1.21
Date: 2022-15-02
MCR54-DUAL
first version
MFL
-
Version: v1.17
Date: 2021-09-15
MFL
improved compatibility with new filters and Manager (MFL passes to Wisycom Manager the range of internal filters)
-
Version: v1.16
Date: 2020-11-20
MFL
New
- Updated external amplifiers list
- Optical power recovery not activated for received optical power below 0.1 mW
- Gain settings on Manual for any switching from IFB mode to nIFB; the E2 mode saved is set when going back to ANT
- Max attenuation setting for all the RF attenuators on start up.
Bug fix
- RF level displayed correctly on Set Gain page for values above 4 digits
- Gain Modulo displayed properly on OPT.CH page
MFLC
-
Version: v1.8
Date: 2020-06-11
MFLC
- added compatibility with FiberBox v3
- fixed wrong management of FRK-V5 and FRK-V6
-
Version: v1.5
Date: 2017-02-08
MFLC
fixed: Ethernet bug: factory reset problem
MPA221
-
Version: v1.2
Date: 2017-02-08
MPA221
fixed: Ethernet bug: factory reset problem
MPR30-ENG
-
Version: v1.15
Date: 2020-10-20
MPR30-ENG
- Added compander alignment with transmitter during SYNC operation
WARNING:
to upgrade from version 1.11 to version 1.15 it is necessary to perform an intermediate upgrade to version 1.12!
therefore do an upgrade from 1.11 to 1.12 and then from 1.12 to 1.15-
Version: v1.14
Date: 2018-04-10
MPR30-ENG
- Added “Panel Lock” parameter (under Settings menu):
– When it is set to”Yes“, all the parameters are locked except the Group/Channel/freq & Audio level (MIC/LINE).
– When it is set to “ENC*“, the device loads the Factory Preset and set the expander to ENC-Wis and the LINE level to +12dBu. All the parameters are locked except the Group/Channel/freq & Audio level (MIC/LINE). - fix: bug on the expander settings: after the loading of the preset with a different expander setting (ex. Exp. current ENR-Wis, expander Preset 1 ENC-Wis) , the expander is loaded correctly (ex. ENC-Wis); but after the reboot of the receiver, the device starts with the previous expander (ex. ENR-Wis)
NOTE: FACTORY PRESET settings:
Headphone: -10dB
Squelch: 12dBuV
Expander: ENR-Wis
Tone sq.: OFF
MIC: -18dBu
Sig. Phase: 0
Display contrast: 3 sec
Display timeout: 15 sec
Off timeout: OFF
LED: Full-
Version: v1.12
Date: 2016-09-07
MPR30-ENG
new – add 180° display rotation: selectable through the menu “Settings>Display>Direction”
MPR30-IEM
-
Version: v2.1
Date: 2016-04-14
MPR30-IEM
new – Battery charger enhancement
new – Enhanced Volume range: -65/+15dB
new – Eliminated Volume lock level at 30mW
new – Quick Menù view current audio volume
new – New Volume lock as in MPR50
fix – Group Scan
fix – Volume bar
fix – Clone issueMPR50-IEM
-
Version: v1.6.0
Date: 2022.06.27
MPR50-IEM
-
-
- Added “Panel Lock” parameter (under Settings menu):
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
- Change name of the filters:
-
-
- Change name of the filters:
-