Version: v1.4.1.D
Date: 2020-12-04
MTP40S
- Added Data Extended: thanks to this feature the transmitter sends through the tone squelch in addition to the battery level also the type of compander (ENR/ENC) and the modulation (WB/NB). The receiver displays a mismatch error if it has set the wrong compander and/or modulation
Version: v1.4.0.J
Date: 2020-11-09 13:53:23
MTP40S
- Added: FW updates installation and management through new software Manager
- Added: commands optimization on Manager
- Changed: Reduce time of starting at 6.5 seconds
- Added: compatibility with Eneloop Pro
Version: v1.30.0V
Date: 2019-01-17 11:28:45
MTP40S
added – management of Narrow Band feature to set during the SYNC automatically the receiver (MPR52, MRK980) in Narrow Band mode
changed – Factory Preset configures the max level of power allows in the set frequency
Version: v1.30.0R
Date: 2018-10-12 14:14:39
MTP40S
added – management of frequency with 4 digits for Band 6 [960-1160MHz] and Band 9 [1240-1260MHz]
Version: v1.30.0P
Date: 2016-12-15 13:29:27
MTP40S
changed – disabled the editing by menu of audio AF input between dB (AF Gain) and dBu (AF Max Level). It is not possible anymore change the AF input between dB and dBu using the menu of the display. It is possible to change it only using the manager.
Version: v1.30.0G
Date: 2016-02-03 13:27:34
MTP40S
add – management 5kHz step: the firmware is able to work at 5KHz of step (instead of 25kHz).
NOTE: to work at 5kHz step, the transmitter has to be pre-configured in the factory.
NOTE: Wisycom doesn’t suggest to upgrade the firmware on devices at 25kHz (standard version) because no new feature is implemented.
Version: v1.30.0F
Date: 2015-07-07 13:25:48
MTP40S
fix – change power up/down delay: increase the delay of RF power up/down from 300ms to 500ms
Version: v1.30.0A
Date: 2015-02-19 13:24:12
MTP40S
new – IrDA enabled at power on: After power on of the transmitter the IRDA interface will be activate as default for 15 seconds in order to allow the user to configure/upgrade the device without to enter on the display submenu.
After about 10 seconds without IRDA activity, the IRDA interface will be automatically disabled.
new – Lithium battery
new – name of transmitter: to identify the transmitter. It is shown on the new NAME menu and can be modify using the MTxxx Manager.
The Tx NAME doesn’t replace the receiver’s name shows in the status menu after a SYNC with a Wisycomm receiver.
new – NAME menu: to show the frequency set on the device and the transmitter name. It is possible to enter quickly in the menu using the combination of buttons CH+GR.
new – INFO menu: to show: FW version, HW version, Serial number, Bandwidth, Bootloader version, Options
new – change unit of measure of AF input by display: between dB (AF Gain) and dBu (AF Max Level)
new – lock/hidden of each parameter: Each parameter can be locked (not editable by display) or hidden (not visible by display) in the Current Setting panel of MTxxx Manager*
new – hidden INFO menu using MTxxx Manager*
changed – lock/don’t care of each parameter of PRESET: for each parameter of Preset it is possible to set separately the propriety of “lock” or “don’t care”
*from MTxxx Manager version 1.1.5
Version: v1.22.0F
Date: 2014-08-06 13:22:47
MTP40S
new – options table: to manage up to 7 options